Home › Concrete cities › New Mexico

Concrete Driveway Cost in New Mexico (2026)

Concrete driveway pours in New Mexico typically run $2,800–$7,600 for a 600 sq ft 4-inch concrete driveway pour at 3500 psi compressive strength. Buried footings must clear the 30-inch design frost line, and the state sits in severe freeze-thaw exposure (ACI F2). New Mexico's combination of high alkaline soil sulfate exposure (S2 ACI 318 category) across the Rio Grande Valley, F2 (severe) freeze-thaw exposure in interior climate zones 4B-5B, and high-altitude UV exposure above 5,000 ft elevation in Santa Fe and Taos forces ASTM C150 Type V sulfate-resistant cement plus 6%+ air-entrainment specification on every New Mexico residential pour — and Santa Fe and Taos historic-district adobe substrates require traditional lime-based mortar matching on every adobe-foundation pour with Santa Fe HDRB historic-district review.

State New Mexico
Cities Covered 7
Typical 600 sq ft 4-inch concrete driveway pour $2,800 – $7,600
BLS cement mason wage $19.42/hr

New Mexico climate, soil & seismic drivers

  • Frost-line trench depth: 30-inch design minimum for buried footings
  • Freeze-thaw exposure (ACI 201.2R): F2 — severe freeze-thaw + de-icer exposure, 5-7% air-entrainment required
  • Typical residential mix: 3500 psi compressive strength
  • Expansive soil risk: Moderate — periodic clay shrink-swell, standard footing reinforcement adequate
  • Sulfate exposure (ACI 318): S2 — severe sulfate exposure, ASTM C150 Type II/V cement required
  • Seismic design category (ASCE 7-22): SDC B — minor seismic risk, standard tie-down requirements
  • Winter de-icer salt exposure: Low — minimal winter de-icer use

New Mexico licensing & permits

  • License status: Statewide license required
  • License board: New Mexico Regulation & Licensing Department — Construction Industries Division (GS-2 Concrete) (official site)
  • Permit: city or county building permit required for residential driveway pour > 100 sq ft; CID GS-2 specialty contractor license required statewide on contracts above $7,200

How concrete driveway costs vary in New Mexico

State-specific code or insurance rule: New Mexico NMSA §60-13 requires every New Mexico concrete contractor exceeding the $7,200 residential threshold to hold a Construction Industries Division GS-2 Concrete specialty license — New Mexico is one of only a handful of Mountain West states with concrete as its own specialty trade license, and the CID Construction Industries Division separately requires Albuquerque and Santa Fe historic-district contractors to satisfy adobe-substrate-prep continuing-education requirements on every covered residential pour, with New Mexico's high alkaline soil sulfate exposure across the Rio Grande Valley forcing ASTM C150 Type V cement on every residential pour.

Cities in New Mexico

Compare concrete driveway pricing for 7 cities across New Mexico.

Albuquerque, NM

Compare local concrete driveway pricing in Albuquerque.

Clovis, NM

Compare local concrete driveway pricing in Clovis.

Farmington, NM

Compare local concrete driveway pricing in Farmington.

Las Cruces, NM

Compare local concrete driveway pricing in Las Cruces.

Rio Rancho, NM

Compare local concrete driveway pricing in Rio Rancho.

Roswell, NM

Compare local concrete driveway pricing in Roswell.

Santa Fe, NM

Compare local concrete driveway pricing in Santa Fe.

Got a quote? Check if it's fair.

Upload your estimate for an instant price and scope review tuned to New Mexico labor and material rates.

Analyze your quote

More state guides

Pricing ranges reflect New Mexico market labor (BLS OEWS cement mason & concrete finisher mean $19.42/hr) and Woogoro regional cost modeling. For the most localized estimate, see your nearest city page above.